Cobra Electronics CP 2507 User Manual

OPERATING INSTRUCTIONS FOR YOUR  
®
Cobra  
C O R D L E S S T E L E P H O N E  
The antenna is in the phone,  
not in your way...and the sound is incredible.  
MODEL CP-2507  
Important Safety Instructions  
When using your telephone equipment, basic safety precautions should always  
be followed to reduce the risk of fire, electric shock and injury to persons,  
including the following:  
1. Read and understand all instructions.  
2. Follow all warnings and instructions marked on the product.  
3. Unplug this product from the wall outlet before cleaning. Do not use liquid  
cleaners or aerosol cleaners. Use a damp cloth for cleaning.  
4. Do not locate base unit near water, for example, near a bath tub, wash bowl,  
kitchen sink, or laundry tub, in a wet basement or near a swimming pool.  
5. Do not place this product on an unstable cart, stand or table. The product  
may fall, causing serious damage to the product.  
6. Slots and openings in the cabinet and the bottom or back are provided for  
ventilation, to protect it from overheating; these openings must not be  
blocked or covered. The openings should never be blocked by placing the  
product in the bed, sofa, rug or other similar surface. This product should  
never be placed near or over a radiator or heat register. This product should  
not be placed in a built-in installation unless proper ventilation is provided.  
7. This product should be operated only from the type of power source indi-  
cated on the marking label. If you are not sure of the type of power supply  
to your home, consult your dealer or local power company.  
8. Do not allow anything to rest on the power cord. Do not locate this product  
where the cord will be abused by persons walking on it.  
9. Do not overload outlets and extension cords as this can result in the risk of  
fire or electric shock.  
10. Never push objects of any kind into this product through cabinet slots as they  
may touch dangerous voltage points or short out parts that could result in a  
risk of fire or electric shock. Never spill liquid of any kind on the product.  
11. To reduce the risk of electric shock, do not disassemble this product, but take it  
to qualified servicemen when service or repair work is required. Opening or re-  
moving covers may expose you to dangerous voltages or other risks. Incorrect  
reassembly can cause electric shock when the appliance is subsequently used.  
12. Avoid using telephone (other than a cordless type) during an electrical  
storm. There may be a remote risk of electric shock from lightning.  
13. Do not use the telephone to report a gas leak in the vicinity of the leak.  
14. Unplug this product from the wall outlet and refer servicing to qualified  
service personnel under the following conditions:  
A. When the power supply cord or plug is damaged or frayed.  
B. If liquid has been spilled into the product.  
C. If the product has been exposed to rain or water.  
D. If the product does not operate normally by following the operating in-  
structions. Adjust only those controls that are covered by the operating  
instructions because improper adjustment of other controls may result  
in damage and will often require extensive work by a qualified techni-  
cian to restore the product to normal operation.  
E. If the product has been dropped or the cabinet has been damaged.  
F. If the product exhibits a distinct change in performance.  
2
Important Safety Instructions (continued)  
The cordless handset operates on batteries, please read and follow instructions:  
A. Use only the battery pack supplied with the unit or identical replacement.  
B. Do not dispose of battery pack in a fire. The cells may explode. Check  
with local codes for possible disposal instruction.  
C. Since released electrolyte is corrosive and may cause damage to eyes or  
skin and may be toxic if swallowed:  
C1. Do not open or mutilate battery pack.  
C2. Always replace the entire battery pack rather than reusing one or  
more cells.  
C3. Do not expose batteries to heat or flame.  
D. Exercise care in handling the battery pack in order not to "short" the bat-  
tery contacts with conducting materials such as rings, bracelets, and  
keys. The battery or conductor may overheat and cause burns.  
The base also has a back-up battery, please read and follow these instructions:  
A. Do not attempt to recharge the battery provided with or identified for use  
with this product. The battery may leak corrosive electrolyte or explode.  
B. Do not attempt to rejuvinate the battery provided with or identified for  
use with this product by heating it. Sudden release of the battery elec-  
trolyte may occur causing burns or irritation to the eyes or skin.  
C. Remove the battery from this product if the product will not be used for  
a long period of time (several months or more) since during this time the  
battery could leak in the product.  
D. Properly dispose of "dead" batteries as soon as possible since "dead" bat-  
teries are more likely to leak in a product.  
E. Do not store this product or the battery provided with or identified for  
use with this product in high-temperature areas. Batteries that are stored  
in a freezer or refrigerator for the purpose of extending shelf life should  
be protected from condensation during storage and defrosting. Batteries  
should be stabilized at room temperature prior to use after cold storage.  
15. Never install telephone wiring during a lightning storm.  
16. Never install telephone jacks in wet locations unless the jack is specifically  
designed for wet locations.  
17. Never touch uninsulated telephone wires or terminals unless the telephone  
line has been disconnected at the network interface.  
18. Use caution when installing or modifying telephone lines.  
Save These Instructions  
3
How To Use Your  
®
Cobra  
Cordless Telephone Model CP-2507  
U.S. PATENT 4876709  
U.S. PATENT 5351284  
Introduction  
Thank you for your purchase of a Cobra¨ Intenna® Cordless Telephone Ñ  
the worlds first and only full-range-power cordless telephone without any  
external antennas!  
No more extending, bending, or breaking the antennas found on other cord-  
less phones Ñ your Cobra Intenna conceals its antenna systems inside the  
handset and base, where they should be, out of your way.  
Now you can install your new Cobra Intenna cordless phone virtually any-  
where. Without cumbersome external antennas to worry about, put your new  
phone anywhere a corded phone can go! Then enjoy the freedom of using  
your new cordless phone all over the house as well as outside in your yard.  
Your new Cobra Model CP-2507 features the Opti Scanª system with 25 se-  
lectable channels (the maximum number available) for optimum interference-  
free use, and 10-number memory dialing. The CP-2507 is also equipped with  
an extra-life battery which allows you to keep the phone away from the base  
for up to 14 days between recharges, Clear Call® PLUS Circuitry with com-  
pander noise-reduction system to ensure corded-phone sound quality, Private  
Call¨ voice scrambling, and Power Protectorª reserve power for operation  
during power outages.  
Please take a moment to review this booklet and become familiar with all of  
the many user-friendly convenience features built into your new Cobra  
Intenna Cordless Phone.  
If you need further assistance installing or using your new Intenna Cordless  
Telephone, please call our consumer “hotline” at 1-773-889-3087.  
NOTE: Some cordless telephones operate at frequencies that may cause inter-  
ference to nearby TV's and VCR's. To minimize or prevent such interference,  
the base of the cordless telephone should not be placed near or on top of TV's  
or VCR's. If interference is experienced, moving the cordless telephone base  
further away from the TV or VCR will often reduce or eliminate the interfer-  
ence.  
CAUTION: Any changes or modifications not expressly approved by Cobra  
could void the user's authority to operate the equipment.  
4
Installation Information  
Maximum range is obtained by installing the base unit in the highest living  
area of your home. The location you choose must be near an electrical outlet  
and a telephone wall jack.  
INTERNAL  
ANTENNA  
HANDSET  
TALK BUTTON  
AC ADAPTER  
CHANNEL  
BUTTON  
FLASH BUTTON  
HOLD BUTTON  
REDIAL BUTTON  
MEMORY BUTTON  
TALK & BATTERY  
LOW INDICATOR  
PULSE/TONE  
SWITCH  
BASE UNIT  
POWER 9V DC JACK  
RINGER  
ON/OFF  
SWITCH  
FIND BUTTON  
CHARGE INDICATOR  
POWER  
PROTECTOR™  
BATTERY  
5
Quick Set-Up Guide  
The following basic steps enable quick and easy installation of your new  
Cobra Intenna Cordless Phone for use on a desk or countertop. You are en-  
couraged to review this complete instruction manual to become familiar with  
all of the operating instructions and features of your new phone.  
NOTE: Before using, connect your new system to AC power (see instruc-  
tions below) to charge it overnight (at least 12 hours) for optimum condi-  
tioning of the rechargeable battery inside the cordless handset.  
1
Insert round connector of power adapter into POWER jack (at rear of  
cordless phoneÕs base; see diagram #1 below). Plug power adapter into  
a standard 120 VAC household electrical outlet. Then place handset in  
base so CHARGE indicator lights (see p. 12).  
BASE UNIT—  
REAR VIEW  
HANDSET  
Diagram #1  
Connecting  
power and  
telephone  
ON/OFF  
RINGER SWITCH  
DC POWER JACK  
4
PULSE/TONE  
SWITCH  
ELECTRICAL  
OUTLET  
2
MODULAR  
PHONE JACK  
ADAPTER  
2
3
4
After charging, remove the twist-tie from the phone cord and plug the  
modular telephone connector into the phone jack on your wall (see above).  
Make sure that the RINGER switch is ON (located on base; see p. 11 for  
details).  
Set the PULSE/TONE switch (at the rear of  
the base) for proper operation (see page 11  
for details).  
Note: Make sure you have charged hand-  
set in base 12 hours before using.  
9V  
5
Install the 9V battery for Power Protectorª  
operation in the base as shown in the  
illustration.  
6
Wall Mounting Instructions  
The following steps enable installation on a new or existing telephone wall-  
mounting plate or directly onto a wall. (Your Cobra Intenna is designed to  
be used with any AT & T, GTE, local phone company or other wall-mounting  
plates that can be purchased from most local electronics stores.)  
¥
¥
¥
Run telephone cord through cord wrap channel on bottom of base. (As shown).  
Plug modular phone connector into telephone wall jack.  
Align mounting studs on the plate to the holes on the bottom of the  
Intenna base; push base onto studs and slide down on the wall plate.  
Modular Phone Jack  
Diagram #2: In-  
stallation on a  
telephone wall-  
mounting plate  
Mounting Studs  
¥
¥
Attach the power adapter to the POWER connection (on the base of the  
phone) and plug into a household AC power outlet.  
To install directly on any wall, youÕll need to provide two screws and  
wall anchors; follow these steps:  
1
Ñ Drill two holes 3 / " apart and insert the wall anchors.  
4
Ñ Drive the screws into the anchors until the head of each screw is  
protruding about 1/8" from the wall.  
Ñ Align the holes in the cordless base over the screw heads; push base  
in and slide down on screws (see diagram #3).  
Ñ Plug modular phone connector into telephone wall jack; attach the  
power adapter to the POWER connection (on the base of the phone)  
and plug into to a household AC power outlet.  
Screw Heads  
Diagram #3:  
Installation  
directly on a wall  
7
Modular Phone Jack  
Using Your Phone  
After charging the handset batteries overnight (at least 12 hours), your  
Cobra Intenna cordless phone will be ready for use.  
ANSWERING/PLACING CALLS AT THE BASE  
¥ To answer a call, just pick up handset from base when the phone rings.  
TALK indicator will automatically light. When call is completed, return  
handset to base without pressing TALK button; your phone automatical-  
ly disconnects.  
¥ To place a call, pick-up handset from base and press and release the  
TALK button (indicator will light). When you hear the dial tone, place  
your call.  
ANSWERING/PLACING CALLS AWAY FROM THE BASE  
¥ The TALK indicator must be off (not lit) when the handset is away from  
the base. The phone is ready to  
ring if a call is received (RINGER  
Switch on the base must be in  
ON position).  
¥ Press and release the TALK  
button (indicator will light) to  
answer or place a call.  
¥ Press and release the TALK  
button when finished with a call.  
TALK indicator light will go off  
and the call will be disconnected.  
Cordless Phone Operational Features  
The following features offer state-of-the-art performance and the ultimate in  
user-friendly convenience with your new Cobra Intenna cordless telephone.  
BATTERY SAVER CIRCUITRY  
The handset of this phone may be kept away from the  
base (TALK indicator OFF) up to 14 days at a time. In  
this condition, it is ready for you to answer or place  
calls by pressing and releasing the TALK button.  
Note: A warning beep tone will sound and the  
TALK/BAT indicator will flash when the handset bat-  
tery needs recharging (see p. 12). The duration of the  
battery charge will depend on your actual use of the  
phone in its remote location.  
8
CHANNEL SELECTION  
25 selectable channels are built into your Cobra Intenna  
for optimum interference-free use.  
If interference begins during a conversation:  
¥ Press and release the CHANNEL button on the  
handset. Your phone will automatically scan and  
advance to the next clear channel. A confirmation  
tone (two double beeps) will sound to indicate a  
successful channel change.  
¥ If an alert tone (3 beeps) sounds, channel change  
was unsuccessful. In that case, move closer to the  
phone base and press CHANNEL button again.  
COMPANDER NOISE REDUCTION  
¨
Your Cobra Intenna has the Cobra Clear Call PLUS compander noise-reduction  
system to minimize background noise for optimum audio performance. The sound  
of your phone will be comparable to the performance of a corded phone.  
DIGITAL SECURITY  
Your Cobra Intenna features 65,000 combinations of digital security coding (in accor-  
dance with FCC regulations) to reduce the chance of interference from your neigh-  
bors' cordless phones. These inaudible, electronic codes are transmitted automatical-  
ly by your phone to establish a secure link between your cordless handset and base.  
FIND  
Find the handset by pressing the Find button on the base. The handset will emit  
a beeping sound for thirty seconds.  
FLASH  
This feature briefly interrupts the phone line so that you may access some of the  
advanced featuresÑ like ÒCall WaitingÓ and ÒThree-Way CallingÓÑ that may be  
offered at extra cost by your local telephone company. Press and release the  
FLASH button on the handset to answer a second phone call or place a conference  
call if you subscribe to these services.  
HEARING AID COMPATIBILITY  
Your cordless telephone handset is compatible with inductively coupled hear-  
ing aids (HAC).  
HOLD  
After you put a call on hold (by pressing the Hold button), your Intenna auto-  
matically releases when you, or someone else, picks up another handset on  
the same line. No need to come back and turn it off, because it turns itself off  
automatically.  
9
SYSTEM  
The revolutionary, patented Intenna hidden-antenna system is a Cobra exclusive.  
Intenna is the worldÕs first and only full-range-power cordless telephone that con-  
ceals the handset and base antennas inside the phone and out of the way. No more  
antennas to extend, bend or break. CobraÕs hidden antennas are perfectly matched  
to your phoneÕs microprocessor circuitry for optimum performance offering the  
ultimate in user-friendly convenience.  
LAST NUMBER REDIAL  
Each time you dial, the phone number youÕre calling is automatically saved in  
a special REDIAL memory. To call that number again at a busy signal, press  
FLASH (without hanging up) to get a new dial tone, then press and release the  
REDIAL button. If you wish to try the call in a few minutes, use TALK to access  
the dial tone, then press and release the REDIAL button. The number will au-  
tomatically be redialed.  
MEMORY DIALING (STORAGE)  
Your Cobra Intenna cordless phone enables you to store up to ten frequently  
dialed phone numbers or emergency numbers. With the TALK indicator light  
off, press and release the MEMORY button ; enter the digits of the phone num-  
ber you wish to store, up to 16 digits; press and release the MEMORY button  
again. Now assign your memory number a position by entering any keypad  
number from 0 to 9. You will hear a confirmation beep. Repeat until all ten num-  
bers are entered. NOTE: for automated banking or alternate long distance ser-  
vice, you may need to program a number which is longer than 16 digits. You  
will need to divide the number between two memory I.D. numbers. Follow the  
steps above.  
MEMORY + TELEPHONE + MEMORY  
NUMBER  
+
I.D. # = CONFIRMATION  
(0Ð9) TONE  
MEMORY DIALING (RECALL)  
To call a number stored in memory, press TALK to get a dial tone; press MEMO-  
RY button. Press the keypad number you assigned to that number and your  
phone will automatically dial the number. NOTE: for longer numbers which you  
have stored in two different I.D. numbers, follow steps above, pressing MEMO-  
RY button again before entering the second number. Use the memory sticker card  
provided to write down the names of each memory position. Keep this in any  
covenient place.  
TALK  
DIAL  
+
MEMORY  
+
I.D.#  
0-9  
= MEMORY  
10  
OUT-OF-RANGE SIGNAL  
If three beeps are heard immediately after the TALK button is pressed, the  
handset is too far away from the base. The handset and TALK indicator will  
automatically turn off. Move closer to the base and then try your call again.  
POWER PROTECTOR™ SYSTEM  
Although the handset is battery powered, the base obtains its power from the  
AC outlet. No AC, no power. This could be of critical importance should an  
emergency occur during a power failure. Many homes are now exclusively  
cordless, leaving them without means to quickly contact emergency services  
in this situation.  
Power Protector helps solve that problem. In the Intenna CP-2507, a 9 volt  
battery allows the base to continue working in the event of a power failure.  
The phone will be usable for up to 2 hours continuously (and up to 3 hours  
with occasional use)Ðlong enough in most cases for the power to be restored.  
Replacement of the Power Protector battery with a fresh high quality alka-  
line battery is recommended every six months and after a power outage  
over 30 minutes. Please refer to page 6 for instructions.  
PRIVATE CALL® VOICE SCRAMBLING SYSTEM  
This feature is automatically activated whenever you use your phone. Built-in  
voice scrambling allows complete calling privacy by scrambling the signals  
between the handset and the base and between the base and the handset,  
making it unlikely that an outside source such as another cordless phone,  
scanner or baby monitor to pick up a conversation from your phone. This  
ensures that you will always have totally private telephone conversations.  
PULSE/TONE SWITCH  
Your Cobra Intenna cordless phone can be used with any  
phone system because it is switchable from pulse to tone dial-  
ing (see switch on back of the base) depending on which ser-  
vice you are using. Mixed PULSE and TONE dialing may be  
used (to access certain long-distance or computerized banking  
services, for example) by selecting PULSE with the base switch  
and then using the button on the handset to temporarily  
PULSE  
TONE  
switch to TONE dialing. Hanging up resets to PULSE.  
RINGER SWITCH  
The OFF/ON switch (located on back of the base) controls  
your cordless handsetÕs electronic ringer; no ring will sound  
in the OFF position.  
OFF  
ON  
RINGER  
11  
®
SECUR-LOC  
This exclusive Cobra electronic circuitry is an added security measure to  
protect your phone line from being accidentally accessed by a neighbor's  
cordless phone. Secur-Loc activates automatically when your cordless hand-  
set is placed into its base.  
Rechargeable Handset Battery Information  
NOTE: Before using your new Cobra Intenna cordless telephone for the  
first time, you must charge the battery overnight (at least 12 hours) for  
optimum long-life conditioning of the nickel-cadmium rechargeable  
handset battery.  
BATTERY RECHARGING  
When your cordless handset battery needs recharging, the following alerts  
will remind you to immediately return the handset to the base for recharg-  
ing (this normally requires at least 12 hours of continuous charging):  
1. The TALK/BAT LOW indicator  
on the handset will flash.  
2. A warning (2 beeps every 30 sec-  
onds) will sound while you are  
using the phone. This indicates  
you have only a few minutes of  
battery power remaining to com-  
plete your conversation before the  
phone disconnects.  
3. When handset has been away  
from the base and needs recharg-  
BEEP  
BEEP  
ing, it will beep at 30 second inter-  
vals for five minutes. After this  
time, the handset will seem  
"dead". It will not flash or beep,  
nor will you be able to get a dial  
tone. Return handset to base for  
recharging.  
NOTE: The CHARGE indicator will  
remain on as long as the handset is in  
the base, even after the batteries are fully  
recharged. The batteries will not be  
damaged if the handset remains in the  
base continuously; the charging system  
is self-adjusting and will never over-  
charge the batteries.  
12  
REPLACING THE HANDSET BATTERY  
The rechargeable NiCad battery in your cordless phone may need to be re-  
placed if the handset will not function when the TALK button is pressed after  
recharging for 12 hours.  
Replacement batteries are available direct from Cobra (see accessories order  
form at the end of this booklet or call 1-773-889-3087).  
1. To remove the battery door, press  
and slide downward.  
2. Carefully disconnect the battery  
pack and dispose of it properly.  
See BATTERY DISPOSAL below.  
3. To replace, observe connection  
orientation and connect the new  
battery and replace the door.  
Return the handset to the base  
and charge the battery overnight  
(at least 12 hours).  
HANDSET BATTERY DISPOSAL  
The rechargeable nickel cadmium (NiCad) battery in this product must be  
recycled or disposed of properly in compliance with all applicable laws.  
Certain states or municipalities require recycling and have established collec-  
tion programs. Please contact your local waste removal authority for instruc-  
tions, or return to Cobra for recycling. Wrap batteries carefully and mail  
postage prepaid to:  
Cobra Electronics Corporation  
"Contains Nickel-Cadmium  
Rechargeable Battery. Must be  
recycled or disposed of properly."  
6500 W. Cortland Street  
Chicago, IL 60707  
Attn: Battery Recycling  
DO NOT PUT BATTERIES INTO  
FIRE OR EXPOSE TO HIGH HEAT.  
THEY MAY EXPLODE.  
Ni-Cd  
CLEANING THE CHARGING CONTACTS  
Clean the two metal charging contacts on the base and handset with a soft,  
dry cloth on a regular basis to ensure optimum performance of the battery-  
charging system. Rubbing alcohol may be used if more thorough cleaning is  
required.  
13  
About Cordless Phone Performance  
Your Cobra Intenna cordless phone uses radio transmission to communicate  
between the base and handset. It is thus subject to occasional interferenceÑ  
static or buzzing noises, for example. These conditions may be caused by  
electrical motors on household appliances, fluorescent lights, electrical storms  
and other sources.  
These steps will enhance the maximum performance of your new phone:  
Change channels by pressing the CHANNEL button on the handset  
if you experience interference.  
Don't cover the upper section of the cordless handset with your  
hand (see diagram below). This may block the internal antenna locat-  
ed at the top of the handset, possibly reducing the phone's range and  
audio clarity. Always hold the handset at the middle or close to the  
bottom.  
Hold the  
cordless handset at  
the middle or bottom  
area of your phone  
for best performance  
and range.  
INCORRECT  
CORRECT  
Avoid resting the handset on your shoulder during conversations;  
this may also block the performance of the internal antenna.  
Avoid plugging your phone's power cord into an active AC outlet  
that also provides power for a major appliance or for charging units  
for cordless appliances (vacuums, screwdrivers, etc.) or other elec-  
tronic devices.  
14  
Cordless Telephone  
Troubleshooting Guide  
If your cordless phone does not seem to operate properly, please check the  
following and refer to the appropriate sections in this booklet for detailed in-  
formation:  
¥
¥
The phone is dead; no indicator lights are on: Are the power  
adapter and telephone cord connected?  
Handset beeps during conversations or when away from the base:  
The batteries need recharging; return the handset to the base for  
overnight recharging.  
¥
¥
Hearing poor audio or added interference during calls: DonÕt  
cover the top section of the handset with your hand or rest the  
phone on your shoulder. This blocks the special internal Cobra  
Intenna handset antenna.  
Handset disconnects, loses performance and/or beeps three times  
when in use away from the base: You may be out of range or your  
batteries may need recharging. Move closer to the base and/or  
recharge batteries.  
¥
¥
Unable to make a call due to interference: Select a new channel.  
Handset wont work after a power outage or after disconnecting  
phone from AC power and then reconnecting it: Return the  
handset to the base for about 15 seconds to automatically match  
the security coding.  
¥
Handset seems "dead.": Battery power has run out; return handset  
to base and charge for at least 12 hours. If handset still seems dead,  
unplug the handset battery for 15 seconds and plug back in and  
then place the handset back on the base for at least 5 minutes. Check  
that charge LED lamp is illuminated.  
¥
¥
Memory dialing does not work: Handset battery may have become  
completely discharged; recharge handset in cradle (12 hours) then  
re-enter your memory dialing numbers (see p. 10).  
Power Failure Reset: Power Protectorª Circuitry will preserve the  
codes set in the handset and base, however, if the battery in the base is  
low in power, you must return the cordless handset to the base for  
about 15 seconds. This automatically matches the digital security codes.  
15  
For technical assistance, please call our Automated Help Desk  
which can assist you by answering the most frequently asked  
questions about Cobra products.  
(773) 889-3087  
24 hours a day, 7 days a week.  
A consumer Service Representative can be reached through this number  
8:00 am - 8:00 pm, Monday through Friday, CST.  
If You Think You Need Service Call 1-773-889-3087  
You may be asked to send your unit to the Cobra factory. It will be necessary to furnish  
the following in order to have the product serviced and returned.  
1.  
For Warranty Repair include some form of proof-of-purchase, such as a mechan-  
ical reproduction or carbon or a sales receipt. If you send the original receipt it can-  
not be returned.  
2.  
3.  
4.  
5.  
Send the entire product. For exampleÑmust include base, handset, cords and  
power adapter furnished with the product.  
Enclose a description of what is happening with the unit. Include a typed or clear-  
ly printed name and address of where the unit is to be returned.  
Pack unit securely to prevent damage in transit. If possible, use the original pack-  
ing material.  
Ship prepaid and insured by way of a traceable carrier; such as United Parcel  
Service (UPS) or First Class Mail; to avoid loss in transit to Cobra Factory  
Service, Cobra Electronics Corporation, 6500 W. Cortland St., Chicago, IL 60707.  
6.  
If the unit is in warranty, upon receipt of your unit it will either be repaired or  
exchanged depending on the model. Please allow approximately 3 to 4 weeks  
before contacting us for status. If the unit is out of warranty a letter will automati-  
cally be sent informing you of the repair charge or replacement charge. If you have  
any questions, please call 1-773-889-3087 for assistance.  
Registered with the FCC  
Please note: This cordless telephone operates under part 15 and part 68 of FCC  
rules. Operation is subject to two conditions: 1) It may not interfere with radio  
communications, and 2) It must accept any interference received, including that  
which may cause undesirable operation. See the Operational Features section of  
this booklet for ways to reduce interference.  
Your telephone company is required by the Federal Communications Commission  
to allow you to connect FCC registered telephones to their lines.  
The FCC requires you to provide information, if requested by the local telephone  
company, about the connection of an FCC registered telephone to their lines. They  
may ask you for the FCC registration number and the ringer equivalence number  
(REN), both of which are on the bottom of the base. They may also ask for the Uni-  
versal Service Order Code (USOC) number, which is RJ-11C.  
It is illegal to use this phone on a party line or to connect it to a coin-operated  
telephone.  
16  
Limited One-Year Warranty  
COBRA ELECTRONICS CORPORATION warrants that its COBRA cordless  
telephone products, and the component parts thereof, will be free of defects in  
workmanship and materials for period of one (1) year from the date of first con-  
sumer purchase. This warranty may be enforced by the first consumer purchas-  
er, provided that the product is utilized within the U.S.A.  
Cobra will, without charge, repair or replace, at its option, defective cordless  
telephone products or component parts upon delivery to the Cobra factory  
Service Department, accompanied by proof of the date of first consumer pur-  
chase, such as a duplicated copy of a sales receipt.  
You must pay any initial shipping charges required to ship the product for war-  
ranty service. The return charges will be at CobraÕs expense if the product is  
repaired or replaced under warranty. For further details concerning procedures for  
obtaining service, see the ÒIf You Need ServiceÓ section of this OwnerÕs Manual.  
Exclusions: This limited warranty does not apply 1) to any product damaged  
by accident, improper line voltage or weather related circumstances; 2) in the  
event of misuse or abuse of the product or as a result of unauthorized alter-  
ations or repairs; 3) to non-defective original equipment Nickel Cadmium re-  
chargeable batteries; 4) if the serial number has been altered, defaced or re-  
moved; or 5) if the owner of the product resides outside the U.S.A.  
All implied warranties, including warranties of merchantability and fitness for  
a particular purpose, are limited in duration to the length of this warranty.  
Cobra shall not be liable for any incidental, consequential or other damages,  
including, without limitation, damages resulting from loss of use or cost  
of installation.  
Some states do not allow limitations on how long an implied warranty lasts  
and/or do not allow the exclusion or limitation of incidental or consequential  
damages, so the above limitations may not apply to you.  
This limited warranty gives you specific legal rights, and you may also have  
other rights which vary from state to state.  
COBRA ELECTRONICS CORPORATION  
6500 W. Cortland Street  
Chicago, Illinois 60707  
In addition to its exclusive series of Intenna cordless telephones and an-  
swering systems, Cobra is also one of AmericaÕs leading brands of CB  
radios and accessories, and Safety Alertª radar/laser detectors.  
17  
Cobra Cordless Phone Accessories  
Description  
Part No.  
Cost Ea. X Qty. = Amount  
NICKEL-CADMIUM BATTERY PACK ASSEMBLY  
WITH CONNECTOR  
For use with model CP-2507  
$15.00  
213-013-9-001  
AC POWER ADAPTER  
For use with model CP-2507  
768-026-N-001 $15.00  
★★ Illinois residents add 7%  
Amount  
★★ Cook Co. residents add .75% (7.75% total)  
★★ Chicago residents add 1% (8.75% total)  
★★ Indiana residents add 5%  
(Tax if applicable  
)
Shipping//handling  
$3.50  
★★ Michigan residents add 4 %  
★★ Minnesota residents add 6%  
★★ Ohio residents add 6%  
Total  
★★ Wisconsin residents add 5%  
Make check or money order (no stamps) payable to:  
Cobra Accessories Dept.  
6500 W. Cortland St., Chicago, IL 60707  
Call 1-773-889-3087 or fax1-773-622-2269 for credit card orders  
Allow 4 to 6 weeks for delivery. Offer valid in Continental U.S. only.  
Please print clearly:  
Name  
Address (Not P.O. Box)  
City  
State  
Zip  
Exp. Date  
Credit Card No.  
Customer Signature  
Circle One:  
Visa  
MasterCard  
Discover  
®
Cobra  
Cobra Electronics Corporation  
6500 W. Cortland Street  
Chicago, IL 60707  
PRINTED IN MALAYSIA  
© 1997 COBRA ELECTRONICS CORPORATION  
480-159-P-001  

HP Hewlett Packard L1506 PX848AA User Manual
Hanns G Computer Monitor JC199D User Manual
Frigidaire FFEC3005LW User Manual
Cypress CY14B108M User Manual
Cypress CY7C1916BV18 User Manual
Cypress CY7C1510KV18 User Manual
Contec 4FITGY 1 User Manual
Cisco Systems ISA500 User Manual
Asus LCD Monitor 90LMB5101T010OUL User Manual
AMD Athlon 10 User Manual