JVC Automobile Electronics GR DVM80 User Manual

For Digital Video Camera  
GR-DVM90, GR-DVM80,  
User’s Manual  
ENGLISH  
GR-DVX90, GR-DVX80,  
WR-DV89U  
Marine Case  
GR-DVX10, GR-DVX9, GR-DVX8  
Names of the parts  
Mounting method and operating method  
for each part  
3
1. Tighten the camcorder’s grip strap.  
1
2. Remove the four buckles on the marine case and open the  
2
4
front lid.  
Align the marks.  
3. Align the mark on the Power Dial  
with the “OFF” mark on the marine  
case.  
PUSH  
OFF  
4. Set the camcorder’s Power Switch to  
RA  
ON)  
“OFF”, then open the LCD monitor  
and insert the camera into the marine  
case.  
Front glass  
3
Place the included anti-fogging silica gel in the gap between  
the camcorder and the marine case to prevent fogging in the  
marine case.  
1.Marine case front lid  
2.Main unit  
3.Buckle  
• Set the camcorder’s MODE Dial to the desired setting.  
• If the camcorder’s Operation Switch is set to “ ”, perform  
settings as required then insert the camcorder into the marine  
START/STOP  
SNAP SHOT  
4.Power dial  
case.  
8
Fit the Zoom Lever projection  
over the Power Zoom Lever  
5.Recording start/stop  
button (START/STOP)  
6.Snapshot button  
(SNAP SHOT)  
ZOOM  
5. Fit the Zoom Lever projection on  
the marine case over the outer  
groove of the Power Zoom Lever  
on the camcorder, making sure that  
it is securely fit.  
7.Zoom lever (ZOOM)  
8.Grip strap  
If the camcorder’s Power  
5
6
7
Switch is not set properly when the  
camcorder is placed in the marine  
case, it could break and/or it could  
damage the Power Dial aligning  
boss on the marine case.  
Strap  
Projection  
Power  
Zoom  
Lever  
6. Before sealing the marine case, check that there is no sand,  
dirt, or other foreign matter on the O-ring mounted on the front  
lid or on the O-ring contact surface on the main unit.  
Also make sure that the inserted silica gel bag is not pinched. If  
you dive with foreign matter trapped  
Before use, this unit must be pre-tested  
to check if there is any water leakage.  
in these areas, water will leak.  
Please read before use.  
7. Check that the O-ring on the front lid  
is correctly mounted in the groove,  
then press in the front lid. Flip down  
the four buckles in the directions  
This marine case is a precision instrument designed to permit safe  
video recording under high water pressure. Please pay careful  
attention when handling the unit before and after use, as explained  
in this user’s manual.  
indicated by the arrows in the figure  
on the right to seal the marine case.  
Align the marks.  
Each part of the marine case has been subject to strict controls  
during the manufacturing process, and the individual functions  
have faced stringent tests during the assembly process. Each marine  
case has also had to pass water-proof inspections using high-  
pressure water testers. However, damage can sometimes occur  
during transport and distribution, or during storage after purchase,  
so before diving always carry out the following pre-use test to  
verify safety.  
8. Turn the marine case’s Power Dial in  
the direction of the arrow while  
pressing it down to set the  
PUSH  
OFF  
camcorder’s Power Switch to  
A
R
E
)
N
”.  
• The camcorder’s Power Lamp  
lights.  
9. To start video recording, press the  
Recording Start/Stop Button.  
To stop video recording, press it again.  
Pre-use test  
• Press the Snapshot Button to perform  
Snapshot recording. If the flash is used,  
its brightness will be darker than usual  
due to the marine case. This is normal  
and is not a malfunction.  
• When recording in the PS-WIDE  
mode, a shadow (eclipse) may  
appear around recorded images.  
Be sure to perform the following pre-use test before diving.  
START/STOP  
SNAP SHOT  
1. Before mounting the camcorder inside the marine case, dive  
with only the empty marine case and test for water leaks.  
• You can easily check for water leaks at a depth of 1 m, where  
there is no water pressure. Be sure to perform this test to  
ensure the safety of your camcorder.  
2. The following are some common causes of water leaks:  
A. The marine case is used without attaching the O-ring.  
B. The O-ring is not mounted in the correct position.  
C. The O-ring is damaged or deformed.  
D. There is sand, dirt, hair or other foreign matter on the O-ring.  
E. There is sand, dirt, hair or other foreign matter on the contact  
surface of the O-ring or on the inside of the lid.  
F. The provided strap or silica gel bag is pinched inside the  
marine case when the lid is closed.  
To protect your camcorder and ensure optimum use, keep the  
examples listed above in mind when using the marine case.  
ZOOM  
10. The zoom can be adjusted with the  
Align the marks.  
Zoom Lever.  
11. When you are finished shooting, set  
the marine case’s Power Dial to  
“OFF” (in the direction of the arrow)  
while pressing it down to set the  
camcorder’s Power Switch to “OFF”.  
• The camcorder’s Power Lamp goes  
out.  
H
S
U
P
OFF  
A
R
E
)
N
NOTES:  
O-ring  
The O-ring is made from rubber and is  
mounted on the front lid.  
Refer to the camcorder’s instructions for  
more information.  
JVC accepts no responsibility for water leakage or damage to  
anything inside the marine case (camcorder, cassette, etc.) due to  
careless usage of this product. Be sure to follow correct procedures  
when using the marine case.  
LYT0655-001A  
 

Indesit Cooktop KP9 F11 S G S User Manual
InFocus Personal Computer Secure Digital SD Memory Stick User Manual
Intel Computer Hardware MFS5000SI User Manual
JVC CD Player GET0622 001A User Manual
Karcher Oven PS640G User Manual
Keating Of Chicago Fryer 10x11 BB Gas User Manual
Kensington Switch Portable 4 Port User Manual
Kompernass DVD Player KH 6517 User Manual
Konica Minolta Oxygen Equipment PULSOX 300 User Manual
Kowa Binoculars TSN 601 User Manual